How do I change the Programming Code on my 264 Deadbolt?

Make sure your door is open and unlocked1. Enter your existing PC (Programming Code).2. Press "Kwikset" then "4" then "Kwikset"3. Enter a new PC. It must be between 4 and 10 digits.4. Press "Kwikset"For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beeping.

Answer

How do I add/delete a one-time User Code on my 264 Deadbolt?

A one-time user code may be used only once, and then it will be deleted immediately after use. Make sure your door is open and unlocked1. Enter your existing PC (Programming Code).2. Press "Kwikset" then "9" then "Kwikset"3. Enter a new User Code. It must be between 4 and 10 digits.4. Press "Kwikset"For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beepingIf User Codes are disabled (example: when you go on vacation), the lock can only be operated by the key and turnpiece until they are enabled again.Make sure your door is open and unlocked1. Enter your existing PC (Programming Code).2. Press "Kwikset" then "8" then "Kwikset"3. Repeat steps 1 and 2 to enable or disable the codes again.For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beeping

Answer

How do I add/delete a user code on my 264 Deadbolt?

Add User Codes: A total of 6 User Codes (and a temporary one-time User Code) may be programmed. Do not program a User Code that is the same as your PC (Programming Code).Make sure your door is open and unlocked1. Enter your Programming Code.2. Press ""Kwikset"" then ""1"" then ""Kwikset""3. Enter a new User Code. It must be between 4 and 10 digits.4. Press ""Kwikset""5. Test the code: While your door is open, lock it and enter your new User Code to make sure it unlocks the door.For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beeping.Delete User Codes:The lock is pre-programmed with a default User Code of 1-2-3-4. It is recommended that you delete this code.Make sure your door is open and unlocked1. Enter your existing PC.2. Press ""Kwikset"" then ""2"" then ""Kwikset""3. Enter the User Code you wish to delete.4. Press ""Kwikset""5. Test the code: While your door is open, lock it and enter the User Code to make sure it no longer unlocks the door.For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beeping.

Answer

How to delete all User Codes on my 264 Deadbolt?

If all User Codes are deleted, the lock can only be operated by the key and turnpiece until a new User Code is added.Make sure your door is open and unlocked1. Enter your existing PC.2. Press “Kwikset” then “3” then “Kwikset”For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beeping

Answer

On my 264 deadbolt, the turnpiece cannot rotate or operate

Remove and reinstall the lock, making sure that the tailpiece is horizontal in steps 4 and 5 here.

Answer

On my 264 deadbolt, After my deadbolt has been working normally, the latch bolt locks up and the turnpiece will not rotate.

Enter your PC, then re-enter the door handing code: Press "Kwikset" then "0" then "Kwikset"

Answer

How do I enable/disable autolock on my 264 Deadbolt?

The Auto-Lock feature automatically re-locks your door 30 seconds after unlocking. This feature is off by default.Make sure your door is open and unlocked1. Enter your existing Programming Code.2. Press "kwikset" "5" "kwikset"3. Repeat steps 1 and 2 to enable or disable Auto-Lock againFor all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beeping.

Answer

How to change Auto-Lock time delay on my 264 Deadbolt?

Make sure your door is open and unlockedYou can set the Auto-Lock time delay between 10 and 99 seconds.1. Enter your Programming Code.2. Press “Kwikset” then “6” then “Kwikset”3. Enter time between 10 and 99 seconds.4. Press “Kwikset”For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beeping.

Answer

What Happens If I Forget My User Code for my 264 Deadbolt?

You can make guesses, but each three consecutive failed attempts will result in the 264 Deadbolt locking out for 60 seconds.If you forgot your user code, there are two options:1. Add new user codes.2. Reset 264 Deadbolt to factory settings to clear existing user codes and add new ones.

Ultimate control.

Get support.

264 Contemporary Keypad Deadbolt

Finishes

Documents

Installation Guide - English

Installation Guide - Spanish

Answers

How do I change the Programming Code on my 264 Deadbolt?

How do I add/delete a one-time User Code on my 264 Deadbolt?

How do I add/delete a user code on my 264 Deadbolt?

How to delete all User Codes on my 264 Deadbolt?

On my 264 deadbolt, the turnpiece cannot rotate or operate

On my 264 deadbolt, After my deadbolt has been working normally, the latch bolt locks up and the turnpiece will not rotate.

How do I enable/disable autolock on my 264 Deadbolt?

How to change Auto-Lock time delay on my 264 Deadbolt?

What Happens If I Forget My User Code for my 264 Deadbolt?

Videos

Community Q&As

Connect with us.

Ultimate control.

Finishes

Documents

Installation Guide - English

Installation Guide - Spanish

Answers

How do I change the Programming Code on my 264 Deadbolt?

How do I add/delete a one-time User Code on my 264 Deadbolt?

How do I add/delete a user code on my 264 Deadbolt?

How to delete all User Codes on my 264 Deadbolt?

On my 264 deadbolt, the turnpiece cannot rotate or operate

On my 264 deadbolt, After my deadbolt has been working normally, the latch bolt locks up and the turnpiece will not rotate.

How do I enable/disable autolock on my 264 Deadbolt?

How to change Auto-Lock time delay on my 264 Deadbolt?

What Happens If I Forget My User Code for my 264 Deadbolt?

Videos

Getting Started with Your Fob - Kwikset Kevo Electronic Bluetooth Enabled Smart Lock

264 Electronic Deadbolt Installation

Community Q&As