Answer

How to enable/disable programming code on my SmartCode 955?

1) A programming code enables you to make changes without needing to access the programming button. This is ideal for landlords to allow programming from the outside, without access to the interior program button. Please note that once a programming code is enabled, the program button is disabled and can be used only to factory reset the lock. 2) Make sure the door is open. Press and release the program button using the Smartkey tool or a paper clip. You will hear two beeps. 3) Press 3. You will hear once short beep and the keypad will flash green. 4) Press Kwikset button. 5) Enter a programming code. It will be between 4-8 digits. The programming code cannot be the same as any user code. 6) Press Kwikset button. 7) Re-enter programming code. 8) Press Kwikset button. You will hear one long beep and the keypad will flash green if successful. If you hear three beeps and the keypad flashes red, it was unsuccessful. Repeat from step 1.

Read More

Answer

On my Smartcode 955, I'm unable to program a code.

For security reasons the first 4 digits of each user code must be unique, for example you are unable to program 48151 and 48152If you have disabled user codes you will not be able to add user codes.

Read More

Answer

How do I change the Programming Code on my 264 Deadbolt?

Make sure your door is open and unlocked1. Enter your existing PC (Programming Code).2. Press "Kwikset" then "4" then "Kwikset"3. Enter a new PC. It must be between 4 and 10 digits.4. Press "Kwikset"For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beeping.

Read More

Answer

How do I change the programming code on my 275 Contemporary Deadbolt?

How to change your Programming Code The Programming Code will not unlock your door. It is an added security feature that is used to set up all functions. The default Programming Code is 0-0-0-0. It is recommended that you change it to a code of your own. 1. Make sure the lock is unlocked and the door is open. 2. Enter your Programming Code - for new installation, default is 0-0-0-0. 3. Press enter arrow. You will hear one beep. 4. Press 4 . 5. Press enter arrow. You will hear one beep. 6. Enter a new Programming Code. It must be between 4 and 10 digits. 7. Press enter arrow. You will hear two beeps if successful. If you hear three beeps, it was unsuccessful. Repeat from step 1 slowly

Read More

Answer

How do I program my Powerbolt 2 lock?

Please open the Powerbolt 2 Programming Instructions pdf.

Read More

Answer

How do I program my SmartCode 913 lock?

1. Open the door. 2. Remove battery cover. 3. Press the program button once. 4. Enter new user code. 5. Press lock button. 6. If programming is successful the keypad will flash green once, and you will hear one beep.

Read More

Answer

Will the SmartCode 955 work with Alexa?

No this is a digital lock, but not a smart lock

Read More

Answer

On my SmartCode 955, how to delete individual user codes?

1. Make sure the door is open. 2. If you have not enabled a programming code, press and release the program button. You will hear two beeps. If you have enabled a programming code, enter you programming code, then press Kwikset. You will hear one short beep and the keypad will flash green. 3. Press 2 to delete a user code. You will hear one short beep and the keypad will flash green. 4. Press Kwikset 5. Enter the user code you wish to delete. Press Kwikset 6. Enter the user code again. 7. Press Kwikset. You will hear one long beep and the keypad will flash green if successful. If you hear three beeps and the keypad flashes red. It was unsuccessful. Repeat from step 1.

Read More